TLE: Carpentry and Masonry Part 6

51) Which wood joint protects the room occupants from seeing outside?
a. Rabbet joint
b. Butt joint
c. Bridle joint
d. Miter joint

52) Which wood joint is used to support the middle of a bench?
a. Dado joint
b. Butt joint
c. Bridle joint
d. Miter joint

53) Which unit is the basic linear unit of an English system?
a. foot
b. meter
c. yard
d. inch

54) Which unit is the basic linear unit of a Metric system?
a. foot
b. meter
c. yard
d. inch

55) If you have 2 ft length of a piece of wood, how long is it in inches?
a. 25
b. 12
c. 22
d. 24

56) If you have 2 yards length of a piece of wood, how long is it in inches?
a. 82
b. 72
c. 84
d. 64

57) 10 yards length of wood is how many feet?
a. 36
b. 35
c. 30
d. 24

58) One decameter of G.I. sheets is how many centimeters?
a. 10
b. 20
c. 100
d. 1,000

59) A 2" x 3" x 12' lumber is how many board feet?
a. 2
b. 6
c. 8
d. 10

60) 5 pcs. of a 1" x 1' x 8' lumber is how many board feet?
a. 30
b. 35
c. 40
d. 45

Key Answers, Explanations, Notes, and Concepts

51) Which wood joint protects the room occupants from seeing outside? a. Rabbet joint b. Butt joint c. Bridle joint d. Miter joint

Answer: a. Rabbet joint

Rabbet joint- is a recess cut into the edge of a workpiece. The piece that extrudes is called the tongue. A rabbet joint is the result of joining a rabbet to another piece of wood, typically to construct shelving and cabinet boxes.

Butt joint- is a technique in which two pieces of material are joined by simply placing their ends together without any special shaping.
Bridle joint- is a woodworking joint, similar to a mortise and tenon, in that a tenon is cut on the end of one member and a mortise is cut into the other to accept it. The distinguishing feature is that the tenon and the mortise are cut to the full width of the tenon member.


Miter joint- connects two 45 degree angled pieces of wood together at a 90-degree angle. They are most commonly used in making frames, crown molding, furniture, cabinets, doors, windows, boxes, and joining architraves.
52) Which wood joint is used to support the middle of a bench? a. Dado joint b. Butt joint c. Bridle joint d. Miter joint

Answer: c. Bridle joint
Dado joint- also sometimes referred to as a housing joint, is a very strong type of carpentry joint commonly across a variety of woodworking projects and especially cabinets and shelving.

Butt joint- is a technique in which two pieces of material are joined by simply placing their ends together without any special shaping.
53) Which unit is the basic linear unit of an English system? a. foot b. meter c. yard d. inch

Answer: d. inch 54) Which unit is the basic linear unit of a Metric system? a. foot b. meter c. yard d. inch

Answer: b. meter 55) If you have 2 ft length of a piece of wood, how long is it in inches? a. 25 b. 12 c. 22 d. 24

Answer: d. 24

1ft = 12inches
56) If you have 2 yards length of a piece of wood, how long is it in inches? a. 82 b. 72 c. 84 d. 64

Answer: b. 72
1yard = 36 inches
57) 10 yards length of wood is how many feet? a. 36 b. 35 c. 30 d. 24

Answer: c. 30

1 yard = 3 ft. 58) One decameter of G.I. sheets is how many centimeters? a. 10 b. 20 c. 100 d. 1,000

Answer: d. 1,000

1 decameter = 1,000 cm. = 10 meters

G.I. = galvanized Iron

59) A 2" x 3" x 12' lumber is how many board feet? a. 2 b. 6 c. 8 d. 10
Answer: b. 6

Bd. ft. (inches)= T"xW"xL"/144 Bd. ft. (feet)= T"xW"xL"/12
60) 5 pcs. of a 1" x 1' x 8' lumber is how many board feet? a. 30 b. 35 c. 40 d. 45

Answer: c. 40

Comments, Suggestions, Corrections, and Clarifications are highly appreciated. Kindly put those in the comments section. Fighting!

Comments

Post a Comment

Popular posts from this blog

TLE: Plumbing 60 Items

Image
1) A person who installs pipes, fixtures and other apparatus to convey and supply water in buildings and to dispose and discharge waste water. a. Carpenter b. Plumber c. Mason d. Mechanic 2) It is a receptacle or vault used to collect organic waste discharged from the house sewer. a. Septic tank b. Manhole c. Water tank d. Waste tank 3) The semi-liquid substance accumulated at the bottom of the septic tank. a. Scum b. Sediment c. Sludge d. Silt 4) An underground tunnel that carries off the drainage and waste matter from a home or town is called: a. Drainage system b. Fixture c. Sewerage d. Sewer 5) The pipe that conveys waste from various fixture other than from the water closet. a. Waste pipe b. Soil pipe c. Vent pipe d. Drain pipe 6) It is a fitting or device that provides liquid seal to prevent the back passage of air. a. Loop b. Fixture c. Sewer d. Trap 7) The tools used to tighten or loosen hexagonal fittings like unions and other metal fittings. a. Pipe vise b. Pliers c. Wrenches...
Read more

TLE: Plumbing Part 4

Image
  31) The following are examples of plumbing fixtures, EXCEPT: a. water closet b. drainage c. shower d. urinals 32) Which statement is NOT true about plumbing standards based on Republic Act 1378 which is known as "Plumbing Law"? a. Each fixture directly connected to the drainage system shall be equipped with a water-sealed trap. b. Plumbing shall be designed and adjusted to use the maximum quantity of water consistent with proper performance and cleaning. c. Water closet must be located in a room which is properly lighted and ventilated. d. No substance which will clog the pipes, produce explosive mixtures, destroy the pipes or their joints or interfere unduly with the sewage disposal process shall be allowed to enter the building drainage system. 33) A compartment that receives solid or liquid waste, located below the normal grade of the gravity system is called ________. a. septic b. sump c. trap d. interceptor 34) Which is true toxic substance? a. Hazardous to human healt...
Read more

TLE: Carpentry and Masonry Part 5

Image
41) Which lumber has wood fibers that are packed closely together? a. Edge-grain b. Angle-grain c. Flat-grain d. Close-grain 42) Which lumber has wood fiber that do not run parallel to the board? a. Edge-grain b. Cross-grain c. Flat-grain d. Close-grain 43) A carpenter makes a picture frame. Which type of joint is appropriate? a. Dado joint b. Tenon joint c. Lap joint d. Miter joint 44) A carpenter fixes shelves of a bookcase. Which type of joint is appropriate? a. Dado joint b. Mortise and Tenon joint c. Lap joint d. Miter joint 45) In which wood joint is the end of one member inserted to hole of the other member? a. Dado joint b. Mortise and Tenon joint c. Lap joint d. Miter joint 46) Which wood joint describes the technique for joining two pieces by putting one side over the other? a. Dado joint b. Butt joint c. Lap joint d. Miter joint 47) Which wood joint describes the technique for joining two pieces by putting one end over the other? a. Dado joint b. Butt joint c. Lap joint d. M...
Read more

LET Reviewers, Books, and PDFs (Organized)

Image
LET Reviewer Reliable File (Organized) LET Reviewer Reliable File (Organized) TLE Major Reviewer Business Math Carpentry Cometology Drafting Electrical 1 Electrical 2 Entrepreneurship Foods Plumbing     The following files and compilation of reviewers are free and working. Please do not overwhelm yourself but only review and use what you need. If you have difficulty accessing the files, kindly  Follow  us on this Blog and  Request Access  after clicking the PDF URL or DM us on Twitter so we can get notified of your request.            You can share this Blog with your friends only by sharing the Blog's link  Privately  or through messages or emails. We are also pleasing you  NOT to repost this website to any Public Platforms  such as  Facebook Groups ,  Posts , and  Stories  so there will be lesser possibility that our website can be b anned or reported by exploitative people.  ...
Read more

TLE: Drafting 100 Items

Image
  1.When a designer or an ordinary person translates his or her own design idea with the use of paper and pencil, what is the name of the activity? A. Architectural delineation B.Freehand Sketching C.Geometric Construction D.Drafting 2.After two dimensional drawings are done and all the shapes and sizes being laid-out, the next step to be executed to complete the process is_. A.Dimensioning B.Tolerancing C.Specifications D.Sectional Drawing 3.With the help of drawing instruments such as T-square and triangles, one produces quick and accurate delineations for an intended project. The process is considered as: A. Drafting B. Pictorial Drawing C. Graphics D. Shape and Size Descriptions 4.Technical drafting involves the manipulation of the elements of geometry to make accurate description of shapes. Which term is referred to by engineering’s and drafting professionals all over world? A. Blueprint Reading B. Geometric Construction C. Line Weight D. Measurement 5.Objects to be drawn are ...
Read more

TLE: Carpentry and Masonry Part 2

Image
11. The strongest form of wood joint applicable for table legs is ________. a. miter b. mortise and tenon c. dado d. butt and lap 12. You are almost finished with your project. One of the procedure below is done before the application of finishing materials. a. cutting b. spraying c. sanding d. varnishing 13. A surfaced lumber where four of its sides are smooth or planed is called: a. S3S b. S2S c. Rough d. S4S 14. In carpentry, splicing or joining of wood using two side blocks is called: a. Lapping b. Scarfing c. Fishing d. Jointing 15. There is considerable number of wood joints. The simplest and easiest to make is ________. a. Lap joint b. Dado joint c. Miter joint d. Butt joint 16. In a wooden floor system, the major horizontal support member upon which the floor system is laid is the ________. a. Floor joist b. Sill c. Header d. Girder 17. A type of roof frame consisting series of triangles used to distribute loads and stiffen the structure of the roof is ________. a. Girts b. Raf...
Read more