LET REVIEWER DAILY: TLE MAJOR

41) Which lumber has wood fibers that are packed closely together? a. Edge-grain b. Angle-grain c. Flat-grain d. Close-grain 42) Which lumber has wood fiber that do not run parallel to the board? a. Edge-grain b. Cross-grain c. Flat-grain d. Close-grain 43) A carpenter makes a picture frame. Which type of joint is appropriate? a. Dado joint b. Tenon joint c. Lap joint d. Miter joint 44) A carpenter fixes shelves of a bookcase. Which type of joint is appropriate? a. Dado joint b. Mortise and Tenon joint c. Lap joint d. Miter joint 45) In which wood joint is the end of one member inserted to hole of the other member? a. Dado joint b. Mortise and Tenon joint c. Lap joint d. Miter joint 46) Which wood joint describes the technique for joining two pieces by putting one side over the other? a. Dado joint b. Butt joint c. Lap joint d. Miter joint 47) Which wood joint describes the technique for joining two pieces by putting one end over the other? a. Dado joint b. Butt joint c. Lap joint d. M...

31) Which lumber has been cut tangentially to the growth rings and the fiber runs about 90 degrees to the face? a. Edge-grain b. Angle-grain c. Flat-grain d. Close-grain 32) Which is the art of building with stone, bricks, concrete blocks of other similar materials? a. Carpentry b. Concrete c. Mortar d. Masonry 33) If you want to go upstairs, which part do you hold on to? a. Handrail b. Tread c. Handle d. Riser 34) If you want to upstairs, which part do you step on? a. Handrail b. Tread c. Handle d. Riser 35) What makes the door swing when you close and open it? a. Door knob b. Door lock c. Door shutter d. Door hinge 36) A carpenter wants to construct a stair, what could be the standard height of the riser? a. 5-6 inches b. 6-8 inches c. 8-10 inches d. 10-12 inches 37) In masonry works, it is necessary to wear protective equipment, EXCEPT: a. mask b. goggles c. gloves d. ear muffs 38) In the construction site, what protects the carpenter from falling objects? a. Hat b. Belt and harness...

21) Which is considered to be the oldest and most commonly used building material? a. Cement b. Wood c. Steel d. Sand 22) A wood which is obtained from conifers and are used for framing? a. Hard wood b. Soft wood c. Dark wood d. Brown wood 23) Which wood is obtained from deciduous trees? a. Hard wood b. Soft wood c. Dark wood d. Brown wood 24) Which is a binding agent that reacts with water to form a hard stone-like substance? a. Glue b. Cement c. Mortar d. Grout 25) Which term refers to inert materials when bound together into a conglomerated mass from concrete? a. Aggregates b. Gravel c. Cement d. Water 26) A lumber that has been sawed, edged, and trimmed in which cutting marks are visible is ________. a. rough b. smooth c. dressed d. worked 27) Which lumber has been put through planing machine which gives fine surface? a. rough b. smooth c. dressed d. worked 28) Which lumber that has been dresses and matched, ship lapped, or patterned? a. rough b. smooth c. dressed d. worked 29) Whi...

11. The strongest form of wood joint applicable for table legs is ________. a. miter b. mortise and tenon c. dado d. butt and lap 12. You are almost finished with your project. One of the procedure below is done before the application of finishing materials. a. cutting b. spraying c. sanding d. varnishing 13. A surfaced lumber where four of its sides are smooth or planed is called: a. S3S b. S2S c. Rough d. S4S 14. In carpentry, splicing or joining of wood using two side blocks is called: a. Lapping b. Scarfing c. Fishing d. Jointing 15. There is considerable number of wood joints. The simplest and easiest to make is ________. a. Lap joint b. Dado joint c. Miter joint d. Butt joint 16. In a wooden floor system, the major horizontal support member upon which the floor system is laid is the ________. a. Floor joist b. Sill c. Header d. Girder 17. A type of roof frame consisting series of triangles used to distribute loads and stiffen the structure of the roof is ________. a. Girts b. Raf...

1. The preparation of good quality lumber includes several stages. When it is dried, the process involved is? a. seasoning b. staining c. lumbering d. logging 2. The smallest division of the metric scale that you can find in the steel rule is ________. a. decimeter b. centimeter c. millimeter d. meter 3. What is the conversion equivalent of one inch to centimeters? a. 25.4 b. 2.54 c. 0.254 d. 0.0254 4. Find the total number of board feet of six pieces of lumber with a dimension of 2" x 4" x 12'. a. 8 bd. ft. b. 96 bd. ft. c. 48 bd. ft. d. 480 bd. ft. 5. A seasoned lumber is ideal for carpentry works. Which among the following is best to use? a. Sun dried b. Kiln dried c. Air dried d. Natural dried 6. There are numerous kinds of saw. When sawing along the grain of wood, you need a ________. a. back saw b. cross cut saw c. rip saw d. circular saw 7. In measuring cylindrical object, what is the appropriate tool to be used? a. ruler b. caliper c. pull-push rule d. meter stick...